H2CAP USER MANUAL

The best design hydrogen water generator

H2CAP Plus Manual_ENG.pdf

WHAT IS H2CAP?

INTRODUCING THE H2CAP

The H2CAP is a hydrogen water generator that comes in a compact size for the best portability. All you need with H2CAP is an USB cable and a 500㎖ bottle.
By making use of the Platinum titanium electrode and platinum PEM membrane, the H2CAP is free of residual chlorine and ozone. Plus, these allow the H2CAP to produce hydrogen water with 1,000ppb ~ 1,500ppb that can last longer.
For the users to test its performance, the H2CAP package comes with the test kit that can measure the DH of the hydrogen water.

For user convenience, additional accessories such as the Descaler and test reagent are available for sale.The H2CAP was certified by Japan Hydrogen Water Promotion Association to produce hydrogen water with more than 1,000ppb Test report number – 218H-221

USAGE PRECAUTIONS

Use drinkable water only. Other beverages such as coffee, beer, and etc. may damage the product.
To prevent the electrode plate drying out, store H2CAP with the upper cap closed.
Do not use H2CAP when the USB port or the cable is wet.
Do not disassemble or modify the product. Free warranties are not available once the seal sticker is damaged.
Do not attach H2CAP too tightly to the bottle.
Be careful not to damage the electrode plate and the membrane.
Once they are damaged, leakage may occur and free warranties will not be available.
Use bottles that are compatible with H2CAP (28mm, 30mm)
Using without any water may damage the product.
Clean promptly when notified with the cleaning alarm to maintain the best performance.
Do not consume the Descaler or the reagent.
Use water temperature lower than 50℃.
Do not disassemble the bottom cap when not necessary.

HOW TO OPERATE THE H2CAP

BEFORE FIRST USE:

For supplying power, H2CAP is compatible with a variety of devices.
* To supply power to H2CAP with smartphones, OTG gender is required. (Supplying power via iPhone is unsupported)

Make sure to remove the white plastic plug at the center of the bottom cap.
H2CAP comes with small amount of water on the electrode plate to keep the product moisturized.
Run the cleaning mode before using the product for the first time. (Refer to our website to learn the detailed cleaning mode)
A Noise of hydrogen gas evaporation may occur upon opening the cap after producing hydrogen.

HOW TO RUN THE CLEANING MODE

Cleaning alarm: H2CAP automatically alarms you when to do the cleaning mode.

Insert one sachet of Descaler with 100㎖ of clean water and shake the bottle until the Descaler is dissolved into the water. Then, turn the bottle upside down.
Connect the USB cable and unplug it when the white LED goes off after 3 seconds. Then, reconnect. The cleaning mode will start automatically and turn off after 2mins.
Once the cleaning mode is completed, dispose the water and rinse 2 to 3 times with clean water.
* Use only the Descaler provided (One sachet at one time)
* Using other cleaning tools may damage the product.
* Do not submerge the product in the water for cleaning purposes.
* You may refer to our videos at for the detailed procedures.

HOW TO PRODUCE HYDROGEN WATER

With water fully filled, attach the H2CAP to the bottle. Then, turn upside down as shown in the image.
When the USB cable is connected, the H2CAP will start automatically to produce hydrogen water.
The production of hydrogen water may take 3mins30sec up to 5mins depending on the condition of the water. (Refer to the specification for details)
Once completed, the orange LED will turn on. * If left unopened for a long time after the hydrogen water production, hydrogen gas pressure may cause small drops of water to come out from the bottom cap. * Running this mode 2 times will produce hydrogen water reaching up to 1,500ppb * Using alkaline water or mineral water will produce hydrogen water reaching up to 1,500ppb * You may refer to our videos for the detailed procedures.

HOW TO DO THE DH TEST

Do the test with water temperature of 25℃~35℃.

Shake the reagent well enough before starting the test.
Pour the hydrogen water to be tested until the indicated line(6cc) of the provided test bottle.
Make 7 drops of reagent to the bottle.
If the reagent drops turn transparent, start adding 1 drop at a time.
The water contains 1,000ppb ~ 1,100ppb of hydrogen if they turn blue on the 11th drop.
* 1 drop equals 100ppb
* Slightly shake the test bottle every time the reagent is dropped.
* DH test results may vary depending on the environment. Use the hydrogen meter for exact results.
* For more exact results, do the test after running the cleaning mode.
* Do not reuse the reagent once opened.
* You may refer to our videos for the detailed procedures.

STORAGE AND MAINTENANCE

When storing for a long time, make sure to put a small amount of clean water and close the upper cap.
When the electrode plate dries out or big bubbles start to show, brush softly with a wet cotton swab to moisturize the electrode plate. Then, do the cleaning mode before using the product.
Keep the product away from high temperature.
When assembling the bottom cap, carefully press the center of the bottom cap and turn it until it’s properly attached to the product. The 　product may not stand well when the bottom cap is not properly attached.
*You may refer to our videos for the detailed procedures.

SPECIFICATION

Product Name	H2CAP/ H2CAP Plus
Size	37.2 Φ * 42.5 mm(H)
Weight	53 g
Power	USB
Electricity Consumption	Max 4.5 W
Recommended Amount	500 ml
Recommended Temperature	H2CAP: 10 ~ 30℃ / H2CAP PLUS: 0 ~ 30℃
Materials	Case	SUS304 (Stainless)
	Body and Upper Cap	Tritan
	Bottom Cap	Non-Toxic Elastomer
	Electrode Plate	Platinum Titanum
Electrolysis Type	2 Chamber Platinum Titanum Electrode + Platinum PEM
Electrolysis Performance	Dissolved Hydrogen(DH) : 1,000 ppb ~ 1,500 ppb
Electrolysis Performance	ORP : -400 mV ~ -800 mV
Operating Time	H2CAP : 5 Mins
Operating Time	H2CAP Plus : 3.5mins~5mins
Manufacturer	IonFarms Co., Ltd.
Country of Origin	South Korea

*Warranty: 1 year

This Warranty does not apply:

1. To protective coatings designed to diminish over time, unless failure has occurred due to a defect in materials or workmanship.

2. To cosmetic damage, including but not limited to scratches, dents, and broken plastic on ports unless failure has occurred due to a defect in materials or workmanship.

3. To damage caused by use with a third-party component or product that does not meet the H2CAP specifications.

4. To damage caused by accident, abuse, misuse, fire, liquid contact, earthquake, or other external cause.

5. To damage caused by operating the H2CAP outside published guidelines.

6. To damage caused by service (including upgrades and expansions) performed by anyone not a representative of Ionfarms or an Ionfarms Authorized Service Provider.

7. To an H2CAP that has been modified to alter functionality or capability without the written permission of Ionfarms.

8. To defects caused by normal wear and tear or otherwise due to the normal aging of the H2CAP.

8. If any serial number has been removed or defaced from the H2CAP.